What did you do with your Thunderbird Today?

Big Scott said:
I heard a noise on the drivers side...

View attachment 15319


View attachment 15320

View attachment 15321


Not sure how this happened nor do I understand how the bushing stayed wedged up there. The last guy that did the alignment a couple years ago was a total douche.
Click to expand...
Yike. That could have gone very badly. Are those Thunderbird/Cougar aftermarket strut rod bushings or from another application? They look different than the usual MN12 parts.
 
XR7-4.6 said:
I have ditched the column gauge pod I grew to absolutely hate…. Which was quite a bit more work than it sounds. The tape holding it on ripped off some of the vinyl paint on the original shroud underneath and required me to strip and repaint it. I kept the toggle switch in the pods key release location I originally used to shut off the wideband but instead rewired it to toggle the fog lights(which I previously wired to always on after the console swap) in one position as well as the DRLs in the other.

View attachment 15322

What of the wideband you ask? It’s over here now 😆

View attachment 15323
Click to expand...

The wideband gauge being way over there would seem far more of an issue than ons the column or A-pillar.

If the bezels weren't such a rare commodity, would you consider mounting it to the bezel in the area around the rear defrost switch?
 
CDsDontBurn said:
The wideband gauge being way over there would seem far more of an issue than ons the column or A-pillar.

If the bezels weren't such a rare commodity, would you consider mounting it to the bezel in the area around the rear defrost switch?
Click to expand...


The column spot just sucks, it pushes against the cluster bezel to where you can’t adjust the column without bending it and from the driver seat it covers over 2/3rds of the tach.

I’m not actually leaving it there, I’m just too lazy to come up with something better. A single A pillar pod would probably be my first choice, but I’d seek out a spare A pillar first as I never intended to keep the wideband permanently installed, I only use it just for the tuning stage

Ericv8thunderbird said:
Ooooo. Do share!
Click to expand...

I stuck a relay inside with the normally closed terminals jumpering the circuits going to the O/T button and used another circuit on the board that has 12v in all positions but Off to energize the relay coil. The relay basically just mimics you holding down the button indefinitely, when you actually use the controls the relay is energized and it operates normally, displaying the interior temp

This only works this simply on SOME 94-97 climate control heads though, this one you can hold down the button and the display will show the temperature indefinitely, other ones cancel after 5 seconds even though you’re still holding down the button.
 
Last edited:
Not my Thunderbird but car adjacent, I changed the oil on my brother's Subaru legacy, pretty easy considering the oil filter is right on top in the engine bay, used an oil I've never used before, Motomaster OE plus full-synthetic, its formulated by shell who also makes Quakerstate and Pennzoil so I figure its actually decent oil for the price, plus. "any oil is better than no oil!"
 
Yet again working on the steering shaft. The piece I made from the 3/4” bar stock I must have shaved a little too much material from making the DD ends. And there was the slightest play in the wheel as a result even with the unisteer U joint cranked down on it. My fix today was simply taking it back apart and sandwiching a piece of .008” feeler gauge in to fill the slack. Hack but fixed!
 
Last edited:
A lot of times I'll use hard copper to take up slack. It'll squezee out of sreel. I pulled out the big power supply today; it's about 100lbs. I will get the fp to get the gas out of my tank.
 
Last edited:
Grog6 said:
A lot of times I'll use hard copper to take up slack. It'll squezee out of sreel.
Click to expand...

The feeler gauge, U joint and shaft section are all stainless, plus it’s got a hard stop on all ends so there’s nowhere for it to squeeze out.

I degreed my cams with feeler gauges too, I know what I’m doing 😁

IMG_6580.jpegIMG_6579.jpeg
 
Last edited:
KevinVarnes said:
Yike. That could have gone very badly. Are those Thunderbird/Cougar aftermarket strut rod bushings or from another application? They look different than the usual MN12 parts.
Click to expand...
They look like the 61 continental bushings I just got to redo mine.

They only way I can see that bushing coming off that rod without splitting open confirms the doucher assessment.
 
Apparently I went Thanksgiving turkey hunting with the car today. It was of the insta-tenderized variety and was super fresh, but alas... I had to abandon it to the elements.

In theory a replacement windshield is coming tomorrow. Thank goodness it's going to be dry for a few days! :facepalm: :zcrazy:

1762970664149.png
 
theterminator93 said:
Apparently I went Thanksgiving turkey hunting with the car today. It was of the insta-tenderized variety and was super fresh, but alas... I had to abandon it to the elements.

In theory a replacement windshield is coming tomorrow. Thank goodness it's going to be dry for a few days! :facepalm: :zcrazy:

View attachment 15377
Click to expand...
That stinks. Glad it wasn't any worse than it was and you were able to find a replacement windshield so easily.
 
theterminator93 said:
Apparently I went Thanksgiving turkey hunting with the car today. It was of the insta-tenderized variety and was super fresh, but alas... I had to abandon it to the elements.

In theory a replacement windshield is coming tomorrow. Thank goodness it's going to be dry for a few days! :facepalm: :zcrazy:

View attachment 15377
Click to expand...

Glad to hear that it's just a windshield and not anything more serious!

On that note, did it get more than just your windshield?

Screenshot_20251112-220549.png
 
I got my catalytic converter guard for my cr-v a couple weeks ago, finally got it assembled and today just painted it with some high heat paint, here's a before and after, I know the paint will eventually come off but I just wanted to dull it down so it wasn't a big "LOOK OVER HERE" that the shiny aluminum was I think it turned out great
Before
IMG_0349.jpg
after
IMG_0351.jpg
then I also took off the side step that's going to get in the way of putting it on and came up with this hack to keep the hardware that was in really good shape after I cleaned it free of rust for the time being until I can figure out how to put the step back on with the guard, its the hardware in a bag with fresh 0w-20 engine oil then two bags on top to keep it from leaking, feel free to tell me why this is a great idea or the worst thing you've ever seen. Is it overkill, yes, probably, but I had the idea and the oil that's good for nothing else and this hardware is worth keeping nice so I don't gotta buy more down the road.
IMG_0357.jpg
 
New glass is in, $299. Pleasantly surprised that they were able to get it in so quickly, and the tech was familiar with MN12s/FN10s too.

He didn't have the right rivets to put the trim back on so he'll be back Monday, but I can at least drive it again. :)

PXL_20251113_162527194.MP.jpg
 
You must log in or register to reply here.

Similar threads

Back
Top